Installation and maintenance methods of angular contact ball bearings
Installation tips
High-speed precision angular contact ball bearings are mainly used in high-speed rotating applications with light loads. They require high-precision bearings, high speed, low temperature and low vibration, and a certain service life. Often used as a support for high-speed electric spindles in pairs, it is a key accessory for high-speed electric spindles of internal surface grinding machines.
Installation form
Angular contact ball bearings can be selected automatically and quickly. There are three types of installation of angular contact ball bearings: back-to-back, face-to-face and tandem arrangement. When installed back-to-back (the wide end faces of the two bearings are opposite), the contact angle of the bearings spreads along the axis of rotation, which can increase the rigidity of the radial and axial support angles and have the largest resistance to deformation. During installation, the contact angle of the bearing converges in the direction of the axis of rotation, and its supporting angle is less rigid. Because the inner ring of the bearing protrudes from the outer ring, when the outer rings of the two bearings are pressed together, the original clearance of the outer rings is eliminated, which can increase the preload of the bearing; when installed in series (the wide ends of the two bearings are in one direction) The contact angles of the bearings are in the same direction and parallel, so that the two bearings can share the working load in the same direction. However, when using this type of installation, in order to ensure the axial stability of the installation, two pairs of bearings arranged in series must be installed opposite each other at both ends of the shaft.
Main Specifications:
1.Bearing accuracy index: exceeding GB / 307.1-94 P4 level accuracy
2. High-speed performance index: dmN value 1.3 ~ 1.8x 106 / min
3. Service life (average):> 1500 h
The service life of high-speed precision angular contact ball bearings has a lot to do with the installation. Pay attention to the following matters
1. Bearing installation should be performed in a dust-free and clean room. Bearings must be carefully selected. Bearing spacers must be ground. The parallelism of spacers should be controlled at 1um while maintaining the same height of the inner and outer ring spacers. the following;
2. The bearing should be cleaned before installation. The inner ring slope is upward during cleaning. The hand induction is flexible and there is no stagnation. After drying, put in the specified amount of oil.
3. Special tools should be used for bearing installation, and the force should be uniform. Knocking is strictly prohibited;
4. The bearings should be stored clean and ventilated, without corrosive gas, and the relative humidity should not exceed 65%. Long-term storage should prevent rust regularly.
Suffix definition
B: Modified internal structure
MP: Machined window brass cage
TVP: glass fiber reinforced nylon cage
UA: Universal structural design for pairs of mounted bearings, small axial clearance bearing set
UO: Universal structural design for pairs of mounted bearings, zero axial clearance bearing set
DA: double half inner ring (double row angular contact ball bearing)
TVH: Glass fiber reinforced polyamide cage, steel ball guide
Maintenance
1. When the bearing runs to a certain period (or maintenance period), remove the bearing completely;
2. Wash the bearings with diesel or kerosene for cleaning. If there are technical conditions, it is best to open the sealing cover for cleaning;
3. Dry and clean the oil after cleaning, check for damage on the appearance inspection;
4. Use a wooden rod of about 150mm in diameter with the same internal diameter as the angular contact ball bearing (preferably a hollow tube), with one bearing fixed at one end;
5. While turning the bearing quickly by hand, put the other end of the wooden stick (wood tube) on the ear or the microphone of the audio amplifier to listen to the bearing rotation noise;
6. After the bearing is fixed, move the stick horizontally to check whether the bearing is worn and loose.
7, FAG bearings with severe looseness, excessive rotation noise, and severe defects should be eliminated and replaced with the same type;
8. Take a bucket and melt the appropriate amount of grease (high-quality yellow dry oil) with gentle heat (not overheating). Put the tested bearing in the bucket and soak it without bubbles. Take out the bearing before the grease cools, the amount of residual grease is small. Angular contact ball bearings are taken out after the grease has cooled, and the amount of residual grease is large. Determine the amount of grease residue as needed.
9. Wipe the grease on the outside of the bearing with a soft cloth or toilet paper to mount the FAG bearing on the pulley as it is, and the maintenance work is over.







